Bionaire BOH2503D Instruction Manual download pdf (Page 2)

PLEASE READ AND SAVE THESE

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic safety

precautions should always be taken including the

following:

1. Before connecting the heater, check that the

voltage indicated on the rating plate corresponds

to the main voltage in your home/ofﬁce.

WARNING: In order to avoid overheating, do

not cover the heater (

) Reference to product.

3. DO NOT position the heater directly under a

power socket.

4. DO NOT use this heater in the immediate

surroundings of a bath, a shower or a

swimming pool.

5. If the supply cord or plug is damaged, it must

be replaced by the manufacturer or its service

agent or similarly qualiﬁed person in order to

avoid hazard. The heater contains no user

serviceable parts. Should the product suffer

damage or breakdown, it must be returned to

the manufacturer or their service agent.

6. Under the environment with electrical fast

transient, the product may malfunction.

7. DO NOT use this heater with a programmer,

timer or any other device that switches the

heater on automatically, since a fire risk

exist s if the heater is covered or positioned

incorrectly.

8. Only touch the heater with dry hands.

9. DO NOT use this heater outdoors.

10. DO NOT position where it can be touched by

children, especially the very young.

11. Allow a safe area around the heater away from

furniture or other objects; at least 50 cm from

the top and sides and 200 cm at the front. The

heater is to be placed at least 3m from water

source.

12. DO NOT use this heater when it is lying on its

side.

13. DO NOT use the heater in rooms with

explosive gas (e.g. petrol) or while using,

oxygen, inﬂammable glue or solvent (e.g. when

gluing or varnishing parquet ﬂoors, PVC etc.)

14. DO NOT insert any objects into the heater.

15. Keep the mains cord at a safe distance from

the main body of the heater.

16. If overheating should occur, the built-in

overheating safety device will switch off the

heater.

17. DO NOT place the cord under a rug.

18. The heater cannot be used adjacent to

curtains or combustible material. Curtains or

combustible material may be burned if the

heater was installed incorrectly.

19.

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

20. This heater is ﬁlled with a precise quantity

of special oil. Repairs requiring opening of

the oil container are only to be made by the

manufacturer or his service agent who should

be contacted if there is an oil leak;

21. When scrapping the heater, follow the

regulations concerning the disposal of oil.

DESCRIPTIONS (See Fig. 1, 2 & 3)

A. Heated fins

B. Vents

C. Pull down handle

D. Power switch

E. Cord Storage

F. Power cord

G. Front castor assembly

H. Digital display

I. Power light

J. Mode light

K. Timer light

L. Mode button

M. Thermostat/timer button

N. Adjuster buttons

O. °F - °C button

P. Front wing nut

Q. Castor

R. Rear castor assembly

S. Rear wing nut

T. U-bolt

Technical Speciﬁcations

BOH2503D: Wattage: 2500W

ASSEMBLY INSTRUCTIONS (See Fig. 3)

Please make sure the heater has not been

plugged into any electricity outlet. Carefully remove

heater from box. Some accessories are packed

internally. Please make sure you have all of the

following accessories prior to throwing away

packaging.

2 Castor assemblies with four castors

(R, G, & Q),

and 2 U Bolts with wing nuts (T, P, S).

Note: This unit is for FLOOR USE ONLY.

1. Turn the heater upside down and you will see

2 U-bolts (T) with wing nuts over the ﬁrst and

last joint of the heater.

2. Unscrew the wing nuts (S & P) from the

U-bolts (T).

3. Start with the front of the unit and place one

hole of the front castor assembly (G) to the L

shape of the U-bolt (T) and the other hole of

the castor assembly into the other end of the

U-bolt, then screw on the wing nut (P).

4. Repeat step 3 for the rear castor assembly,

using wing nut (N) instead of wing nut (K) and

rear castor assemblies (M).

5. Use your hand to press the four casters (L)

onto the four axis of the two foot plates until

you hear them click into place. Use your hand

U.K. and IRELAND

to turn the castors and if the move smoothly

they have been installed properly.

6. After installation of the front and rear castor

assemblies and the castors turn the heater

the right way up: the heater is now ready

for use.

NOTE: Make sure when assembling that the

castor assemblies with wheels are pointing

outwards for maximum stability.

OPERATING INSTRUCTIONS

(See Fig. 1&2)

1. Ensure the power switch (D) is set to the OFF

(O) position.

2. Plug in heater.

3. Flip the power switch to the ON (-) position. The

power light (I) will illuminate red until the unit is

unplugged.

4. Press the mode button (L) once to activate the

unit. The mode light (J) will glow green to indicate

the heater is running. The unit will automatically

start on Setting 3 (High Heat).

5. Press the mode button until the desired heat

setting is shown on the digital display (H).

BOH2503D: 3=2500W, 2=1300W, 1=1200W,

=Energy Saving Mode

After using the heater, press the mode button

until the unit is deactivated and the mode light

turns off, then turn the power switch to the OFF

position. Unplug the heater from the socket.

SETTING THE THERMOSTAT

1. Set the desired heat setting by pressing the mode

button.

2. Press the thermostat/timer button (M) once to

activate thermostat setting. The room temperature

and a thermostat icon ﬂash on the display.

3. Press the + or - adjuster buttons (N) to select the

desired temperature. (Range 12° C - 30° C)

4. The thermostat symbol will stop ﬂashing. The

thermostat control will now automatically maintain

the preset temperature level by turning the heater

on and off.

5. To deactivate the thermostat setting, press

the thermostat/timer button continuously until

the thermostat symbol does not appear on the

display.

NOTE: The Power light will remain lit during

operation.

NOTE: It is normal for the heater to cycle ON

and OFF as it maintains the preset temperature.

FROST GUARD INSTRUCTION

When the heater is in frost guard mode, the

temperature will be maintained at 5° C; thus the

heater will be in the off status unless the room

temperature is lower than 5° C. If the room

temperature is lower than 5° C, the heater will

automatically start working and will keep turning

on & off all the time, maintaining its ambient

temperature of 5° C. To activate, press the

mode button to turn the unit on, then press the

thermostat/timer button twice. The (

) icon will

display to indicate that frost guard is activated.

USING THE TIMER

Programmable timer

The user can programme the heater to turn

OFF after a selected period or to come ON at a

preset time.

Setting the OFF timer

1. Select the mode and temperature you want

the heater to run.

2. Press the thermostat/timer button 3 times.

The OFF timer icon ﬂashes.

3. Using either the (+) or (-) adjuster buttons,

programme the heater to turn off up to 24

hours later, in increments of 1 hour.

Example - 9 hours

4. After setting the time, the digital display

will stop ﬂashing to show the timer is

activated. The timer will count down until the

predetermined length of time has passed, and

the heater will then automatically switch off.

Example - Switch OFF - The time is 1 pm. The heater

is running and you require the heater to switch off at

10 pm; therefore, set the time to 9 hours.

Setting the ON timer

1. If the heater is on, press the thermostat/timer

control button 4 times. The ON timer icon ﬂashes.

2. Using either the (+) or (-) adjuster buttons,

programme the heater to switch on up to 24

hours later, in increments of 1 hour.

Example - 4 hours

3. After setting the ON timer, the digital

display will stop ﬂashing to show the timer is

activated. The timer will count down until the

predetermined period has passed, and then the

heater will automatically switch on.

NOTE: When the ON timer is set, the unit will

remember the setting the unit was previously on

and activate to this setting after the predetermined

period. The heat setting may be changed after

setting the timer by pressing the mode button.

ENERGY SAVING MODE

To activate, press the mode button until

appears on the display. The heater will operate

on a cycle – 10 minutes on High (2500W) and

30 minutes on Medium (1300W). When the

temperature is at or above 85ºF (30ºC), the

heater will ignore the 10 minute High setting and

operate on Medium for 30 minutes immediately.

The cycle repeats while in this mode.

DISPLAY PREFERENCES

The default setting on the digital display is

degrees Celsius (°C). To switch to degrees

Fahrenheit (°F), press the °F-°C button.

NOTE: Unit must be unplugged for it to be fully off.

TIP OVER PROTECTION

When the unit is accidentally knocked over, or

tilts on one side at more than a 45° angle; it

BOH2503D

Fig. 1

Fig. 2

F C

Fig. 3

1 2

RADIATOR 1
BOH2503D 2

Comments to this Manuals

No comments

Bionaire BOH2503D Instruction Manual Page 2

Comments to this Manuals

Related products and manuals for Space heaters Bionaire BOH2503D