Bionaire BW2300 Owner's Manual download pdf (Page 2)

Step 2: To turn the fan on press the Speed Control Button.

Step 3: Set the speed to high, medium (med) or low by

pressing the Speed Control Button.

Step 4: Set the airflow direction to Exhaust (out), Intake (in)

or exchange (one blade blowing air in and the

second blade blowing air out) by pressing the air

flow button.

Step 5: To turn the fan off press the Speed Control Button

until the fan stops.

AUTOMATIC OPERATING INSTRUCTIONS

Your window fan is equipped with the digital control

thermostat that automatically turns the fan on and off

depending upon the preset comfort level. For example, if

you have set your thermostat to 75 degrees and the room

temperature drops to 74 degrees or lower then the fan will

automatically shut off. The fan will then turn on again when

the room temperature exceeds 75 degrees. In order to

take advantage of this feature, make sure your window fan

is in automatic mode (this will be indicated by a red light on

the left of the control panel).

Step 1: Set the fan to Automatic Mode by pressing the

Mode button located on the Control Panel. The

Auto On light will illuminate when the unit is in

Automatic Mode.

Step 2: Press the Temp Set (+,–) buttons on the front of

the Control Panel or use the remote control to

program the desired temperature or switch to the

manual mode.

Step 3: When you are finished setting the temperature, let

go of the button. The display will blink a few times

and then will return to displaying the current room

temperature.

IMPORTANT: If the unit will not start in automatic mode,

please make sure that the set temperature is below the

current room temperature. If the fan is stopped and you

would like to turn it back on, lower the set temperature or

switch to the manual mode.

REMOTE CONTROL INSTRUCTIONS

Your window fan is equipped with a remote control. This

remote control can be used to adjust the following

functions: Power, Manual/Automatic mode, Air Flow

Direction, Temperature adjustments.

Two “AAA” batteries have been included for your

convenience.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc),or

rechargeable (nickel-cadmium) batteries.

CLEANING/MAINTENANCE INSTRUCTIONS

Follow these instructions to correctly and safely care for

your fan. Please remember:

• Always unplug the fan before cleaning.

• Do not allow water to drip on or enter into fan housing.

• Be sure to use a soft cloth moistened with a mild soap

solution.

• Do not use gasoline, thinner or benzene as a cleaner.

Step 2: If the fan does not fit snugly to the top and bottom of

the window casing, attach the included extender

panel(s) and pull out the built-in extender screen until

the fan fits safely in your window (See Figure 3).

Step 3: To keep the fan in place, carefully close the

window so that the bottom edge of the window

rests on the flat area on the top of the window fan.

WARNING: Be sure fan is securely installed in your

window at all times. Do not lean or push on fan while it is

in the window.

NOTE: For slider windows, set the fan vertically in your

window opening, with the left side on the bottom.

INSTALLATION GUIDE

The extender panels can be secured to the fan by simply

sliding the extender panels into the grooves located on the

left hand side of the fan.

The extender screen can be adjusted by pulling out the

extender locks located on the top and bottom of the right

side of the fan. Push the locks back into place to secure

the extender screen at the desired length.

For 24 inch to 27 inch (61-69cm): Use up to 3 inch

(7cm) of right side, pull out extender screen.

For 28 inch to 34 inch (71-86cm): Use one 3 inch (7cm)

extender panel on the left side. Adjust the pull out extender

screen on the right side for a tight fit

(from 0.5 inch to 7 inch (1.3-17.8cm) ).

For 35 inch to 37 inch (89-94cm): Use two 3 inch (7cm)

extender panels on the left side. Adjust the pull out

extender screen on the right side for a tight fit

(from 0.5 inch to 7 inch (1.3-17.8cm) ).

Larger than 37 inch (94cm): Additional extender panels

will be required.

MANUAL OPERATING INSTRUCTIONS

NOTE: To operate the fan continuously, make sure that the

auto on light located to the left of the control panel is off.

Step 1: Plug your window fan into any 120V AC electrical

outlet.

NOTE: The temperature display will always be on when

the fan is plugged into the electrical outlet.

FAN SAFETY

PLEASE READ AND SAVE

THESE IMPORTANT

SAFEGUARDS

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic safety precautions

should always be followed to reduce the risk of fire, electric

shock, and injury to persons, including the following:

1. Read all instructions before using the appliance.

2. To avoid fire or shock hazard, plug the appliance

directly into a 120 V AC electrical outlet.

3. Keep the cord out of heavy traffic areas. DO NOT let

the cord hang over the edge of a table or counter. To

avoid fire hazard, NEVER put the cord under rugs,

near heat registers, radiators, stoves, or heaters.

4. To protect against electrical hazards, DO NOT

immerse in water or other liquids. Do not use near

water.

5. Close supervision is necessary when any appliance is

used by or near children or disabled people.

6. Always unplug the fan before moving it, putting on or

taking off parts, cleaning, or whenever the fan is not in

use. Be sure to pull by the plug and not the cord.

7. Avoid contact with moving parts. DO NOT operate

without fan grills properly in place.

8. DO NOT operate any appliance with a damaged cord

or plug, if motor fan fails to rotate, after the appliance

malfunctions, or if it has been dropped or damaged in

any manner. Return appliance to manufacturer for

examination, electrical or mechanical adjustment, or

repair.

9. DO NOT operate in the presence of explosive and/or

flammable fumes.

10.Use appliance only for intended household use as

described in this manual. Any other use not

recommended by the manufacturer may cause fire,

electric shock, or injury to persons. The use of

attachments not recommended or sold by Bionaire

may cause hazards.

11.DO NOT use outdoors.

12.Always use on a dry, level surface.

13.Keep unit away from heated surfaces and open flames.

14.DO NOT attempt to repair or adjust any electrical or

mechanical functions on this unit. Doing so will void

your warranty. The inside of the unit contains no user

serviceable parts. All servicing should be performed

by qualified personnel only.

PLEASE SAVE THESE

INSTRUCTIONS

CONSUMER SAFETY INFORMATION

THIS APPLIANCE HAS A POLARIZED

AC PLUG (one blade is wider than the

other). To reduce the risk of electric

shock, this plug is intended to fit in a

polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the

plug. If it still does not fit, contact a

qualified electrician to install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR

DEFEAT THIS SAFETY FEATURE IN ANY WAY.

PLEASE READ AND SAVE

THESE IMPORTANT

SAFETY INSTRUCTIONS

WINDOW FAN INSTALLATION

The window fan has been designed to fit double-hung,

slider and casement windows.

Step 1: Set the fan into your window opening.

INSTALLATION INSTRUCTIONS

Figure 1

PULLS OUT UP TO 7.0 inch (17.8cm)

LEFT

Extra Extender Panels

RIGHT

Built-In, Pull Out Extender Screen

24 inch (61cm) long

FRONT VIEW

Two 3.0 inch (7cm) extenders, (Included in your box packed at both ends)

Figure 3

Figure 2

G. Speed Control Button J. Mode Button

H. Temp Up Button K. Dimmer Button

I. Air Flow Direction Button L. Temp Down Button

A. Front Grills

B. Extender Screen (not shown)

C. Extender Locks(2)

D. Control Panel

E. LCD Display

F. Remote Control

BW2300_07EM1. qxd:BW230006EM1. qxd 11/17/07 8:38 AM Page 2

1 2

Comments to this Manuals

No comments

Bionaire BW2300 Owner's Manual Page 2

Comments to this Manuals

Related products and manuals for Household fans Bionaire BW2300