Bionaire BFH3520 - 2 Instruction Manual download pdf

7. Do not use this heater with a programmer,

timer or any other device that switches the

heater on automatically, since a fire risk exists if

the heater is covered or positioned incorrectly.

8. Only touch the heater with dry hands.

9. DO NOT position where it can be touched by

children, especially the very young.

10. DO NOT use this heater outdoors.

11. Allow a safe area around the heater away

from furniture or other objects; at least 50 cm

from the top and sides and 200 cm at the

front.

12. Do not use this heater when it is lying on its

side.

13. DO NOT use the heater in rooms with

explosive gas (e.g. petrol) or while using

inflammable glue or solvent (e.g. when

gluing or varnishing parquet floors, PVC etc.)

14. DO NOT insert any objects into the heater.

15. Keep the mains cord at a safe distance from

the main body of the heater.

16. If overheating should occur, the built-in

overheating safety device will switch off the

heater.

17. Do not place the cord under a rug.

18. The heater is to be installed so that switches

and other controls cannot be touched by a

person in the bath.

19. Avoid the use of an extension cord because

it may cause the heater to overheat.

For U.K. and Ireland only:

If the plug is not suitable for the socket outlets in

your home, it can be removed and replaced by a

plug of the correct type. Please refer to

"Installation of a plug" below.

Installation of a plug

Applicable to U.K. and Ireland

The wires in the mains lead are coloured as such:

BROWN - LIVE

BLUE - NEUTRAL

Please note that the colour of these mains wires

may not correspond with the colour markings

that identify the terminals in your plug. Please

proceed as follows:

The BROWN coloured wire must be connected

to the terminal, which is marked with the letter

"L" or is coloured RED.

The BLUE coloured wire must be connected to

the terminal, which is marked with the letter "N"

or is coloured BLACK.

DO NOT CONNECT either of these wires to the

earth terminal in the plug. The earth terminal plug

is marked with the letter "E", or with the earth

symbol or coloured GREEN and YELLOW.

NOTE: If the terminals in the plug are not

marked or if you are unsure or in doubt about

the installation of the

plug please contact a

qualified electrician.

If a 13A 3-pin plug is

fitted, it must be an

ASTA approved plug,

conforming to

BS1363 standard.

Replacement 13A

fuses must be BSI or

ASTA BS1362

approved.

GUARANTEE

PLEASE KEEP YOUR RECEIPT AS THIS WILL

BE REQUIRED FOR ANY CLAIMS UNDER THIS

GUARANTEE.

• This product is guaranteed for 2 years.

• In the unlikely event of breakdown, please take

it back to the place of purchase, with your till

receipt and a copy of this guarantee.

• The rights and benefits under this guarantee

are additional to your statutory rights which

are not affected by this guarantee.

• The manufacturer undertakes within the

specific period, to repair or replace free of

charge, any part of the appliance found to be

defective provided that:

•We are promptly informed of the defect.

• The appliance has not been altered in any

way or subjected to misuse or repair by a

person other than a person authorised by

the manufacturer.

• No rights are given under this guarantee to a

person acquiring the appliance second hand

or for commercial or communal uses.

• Any repaired or replaced appliance will be

guaranteed on these terms for the remaining

portion of the guarantee.

THIS PRODUCT IS MANUFACTURED TO

COMPLY WITH THE E.E.C. DIRECTIVES

73/23/EEC, 89/336/EEC AND 98/37/EEC.

Waste electrical products should

not be disposed of with

Household waste. Please recycle

where facilities exist. Check on

the following website for further

recycling and WEEE information:

www.bionaire.com/europe or

e-mail [email protected]

13 amp

Setting the Off Timer:

1. Select the Mode and/or temperature you wish

the heater to run in.

2. While the heater is running, press and hold

the up (+) and down (-) buttons simultaneously.

3. By pressing the up (+) and down (-) buttons,

program the heater to turn off in up to 16 hours

from the current time, in increments of 1 hour.

4. After setting the timer, the LCD display will

return to show the current room temperature.

An LED will illuminate to show that the timer is

activated.

5. After the predetermined length of time has

passed, the heater will automatically shut off.

Setting the On Timer:

1. While the heater is off, press and hold the up

(+) and down (-) buttons simultaneously.

2. By pressing the up (+) and down (-) buttons,

program the heater to turn on up to 16 hours in

advance of current time, in increments of 1 hour.

3. After the preset length time of time has passed,

the heater will automatically turn on to auto mode

HI power at 24°C for a preset time of 2 hours.

OSCILLATION INSTRUCTIONS

Press ( ) button J to start and ( ) button J

again to stop oscillation.

REMOTE CONTROL INSTRUCTIONS

Before operation, insert 2 “AAA” batteries (not

included) into the back of the remote control. Remove

batteries before discarding the remote control.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or

rechargeable (nickel-cadmium) batteries.

The remote control for this unit has the capability

of operating all control panel functions (see Fig.

3, 4).

POWER: To turn the unit on press the

Mode ( ) button. To turn the unit off press the

Mode ( ) button.

MODES: To scroll through the various modes

FA, HI, LO, AH, AL and AF press the Mode ( )

Button until you reach your desired setting.

OSCILLATION: To start oscillation, press the

Oscillation ( ) Button once. To stop oscillation

press the button again.

TEMPERATURE: The temperature can be

adjusted only when the unit is set on the Auto

Mode Hi (AH) and Auto Mode Lo (AL).To

increase the temperature setting, press the (+)

button. To decrease the temperature setting that

you desire press the (-) button.

TIMER: To activate the timer from the remote

control, press the Timer Button ( ). From there

you can press the (+) or (-) button, which will

give you the ability to program the heater to turn

on or off in 1 hour increments, up to 16 hours.

For more information see Using Programmable

Timer instructions above.

AUTO SAFETY SHUT-OFF

This heater is equipped with a technologically

advanced, safety system that requires the user

to reset the heater if there is a potential overheat

situation. When a potential overheat temperature

is reached, the system will automatically shut

the heater off. It can only resume operation

when the user resets the unit.

To reset the heater

1. Press the MODE ( ) button.

2. Unplug the heater and wait for 30 minutes for

the unit to cool down.

3. After the 30 minutes, plug the unit in again

and operate normally.

Tip Over Protection

When the unit is accidentally knocked over, it will

instantly shut off. To reset, simply place the

heater in an upright position.

Safety Back-Up Fuse

In the unlikely case the heater does not respond

to an overheat situation, the safety back-up fuse

will engage. In this case, the heater will not

reset. Please contact your local service number

for advice.

PLEASE READ AND SAVE THESE

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic safety

precautions should always be taken including

the following:

1. Before connecting the heater, check that the

voltage indicated on the rating plate

corresponds to the main voltage in your

home/office.

2. WARNING: In order to avoid overheating,

do not cover the heater ( ).

3. DO NOT position the heater directly under a

power socket.

4. Do not use this heater in the immediate

surroundings of a bath, a shower or a

swimming pool.

5. If the supply cord or plug is damaged, it must

be replaced by the manufacturer or its

service agent or similarly qualified person in

order to avoid hazard. The heater contains

no user serviceable parts. Should the

product suffer damage or breakdown, it must

be returned to the manufacturer or their

service agent.

6. Under the environment with electrical fast

transient, the product may malfunction and

require user to reset the product.

9100020007277

BFH3520IUK06EM2

BFH3520

2.4KW digital

TOWER heater

INSTRUCTION MANUAL

Holmes Products (Europe) Ltd

1 Francis Grove

London SW19 4DT

England

Fax: +44 (0)20 8947 8272

Email: info-europe@theholmesgroup.com

Website address: www.bionaire.com/europe

UK - Free phone Customer Service Helpline – 0800 052 3615

Bionaire

, the Bionaire logo

and AccuTemp Plus

are trademarks of JCS/THG, LLC.

BFH3520IUK06EM2 V new.qxd 6/16/06 15:13 Page 1

1 2

Summary of Contents

Page 1 - TOWER heater

7. Do not use this heater with a programmer,timer or any other device that switches theheater on automatically, since a fire risk exists ifthe heater

Page 2 - U.K. and IRELAND

BFH3520ABCDEFFig. 1HGDESCRIPTIONS:A. Heater HousingB. NeckC. Pedestal Pole with 2 HalvesD. BaseE. Locking NutF. Power CordG. Remote Control SensorH. P

Bionaire BFH3520 - 2 Instruction Manual

Browse online or download Instruction Manual for Household fans Bionaire BFH3520 - 2. Bionaire BFH3520 - 2 Instruction manual User Manual

Summary of Contents

More documents for Household fans Bionaire BFH3520 - 2

Comments to this Manuals

Bionaire BFH3520 - 2 Instruction Manual

Browse online or download Instruction Manual for Household fans Bionaire BFH3520 - 2. Bionaire BFH3520 - 2 Instruction manual User Manual

Summary of Contents

More documents for Household fans Bionaire BFH3520 - 2

Comments to this Manuals

Related products and manuals for Household fans Bionaire BFH3520 - 2